This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36235 3c298f89-4303-0410-b956-a3cf2f4a3e73
Parse the cpu port from swconfig and explicitly mark the cpu port as tagged.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35911 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.
This makes OpenWrt always use vlan1 and vlan2 instead.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35704 3c298f89-4303-0410-b956-a3cf2f4a3e73
This contains the following new bigger changes:
* new partition parser which still could lake some features or have bugs
* new nand flash driver
* using physmap-flash flash driver for parallel flash
* some changes to the serial flash driver
With these changes OpenWrt starts using more of the mainline flash drivers.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35632 3c298f89-4303-0410-b956-a3cf2f4a3e73
Do not try to load bcm57xx.ko any more this is not needed for kernel 2.6 and 3.X
Ask the switch driver where the CPU port is.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35624 3c298f89-4303-0410-b956-a3cf2f4a3e73
The included patch will generate a correct network configuration on the simpletech simpleshare.
Thank you for the patch Will Holmes (RealOpty)
This closes#12361.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35623 3c298f89-4303-0410-b956-a3cf2f4a3e73
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to
be expanded. Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could
a similar method be used in "/etc/init.d/netconfig"?
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35491 3c298f89-4303-0410-b956-a3cf2f4a3e73
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.
Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34995 3c298f89-4303-0410-b956-a3cf2f4a3e73
In addition check_module is not needed, nobody checks the return value.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34993 3c298f89-4303-0410-b956-a3cf2f4a3e73
The behaviour of calling 'mount' differed depending on whether it called
the busybox-mount, the mount of util-linux, the mount defined in
/lib/functions.sh and /lib/functions/boot.sh
/etc/preinit even included /lib/functions.sh and /lib/functions/boot.sh,
both re-defining 'mount'.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34792 3c298f89-4303-0410-b956-a3cf2f4a3e73
Sometimes the port 0 was the WAN port or there could be some device
where the port 0 is not wired to an actual Ethernet port. Now telnet in
failsafe will listen on all ports of the switch so user do not have to
search for the correct port any more. This change will make the switch
leak traffic between the WAN and the LAN port, but you should not use
failsafe while connected to a untrusted network.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33544 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hi,
this patch adds the correct vlan definitions for the Siemens SE505v2. It
applies to trunk as well as backfire (please apply here too). On
backfire this also patches brcm-2,4, because brcm47xx base-files is just
symlinked to brcm-2.4.
It also fixes two whitespace issues.
Tested with brcm47xx on both trunk and backfire branch and works as
expected.
Signed-off-by: Manuel Munz <freifunk@somakoma.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28336 3c298f89-4303-0410-b956-a3cf2f4a3e73
