Thank you Javier Achirica for the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38008 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38001 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37977 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most of the Linksys devices without an own GPIO configuration where
detected as WRT54G. On one board this made OpenWrt to boot into
failsafe every time, because one GPIO configurated as button was not a
button.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37970 3c298f89-4303-0410-b956-a3cf2f4a3e73
The imx sata module has only been backported to imx6 target. This change will
fix buildbot errors due to missing patches in other targets. Keep this until
all targets use kernel version with imx sata support in them.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37950 3c298f89-4303-0410-b956-a3cf2f4a3e73
- enable using hwmon GSC driver on all targets
- add a kmod package for it
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37933 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the following error:
firewire_core: Unknown symbol crc_itu_t (err 0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37902 3c298f89-4303-0410-b956-a3cf2f4a3e73
linux-firemware contains the same version we loaded without this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37901 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the following error:
xfs: Unknown symbol exportfs_decode_fh (err 0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37900 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the following error:
keyspan: Unknown symbol ezusb_fx1_ihex_firmware_download (err 0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37899 3c298f89-4303-0410-b956-a3cf2f4a3e73
This enables usage of the ath10k driver on OpenWrt. Only 2.0 PCI hardware
is supported. The ath10k firmware is currently only available
through github so use that as its source for now.
This goes build tested, not run time tested.
[Hauke: I did some minor changes]
Cc: ath10k@lists.infradead.org
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Mathieu Olivari <mathieu@qca.qualcomm.com>
Cc: Jerome Proffit <jproffit@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Matthew McClintock <mmcclint@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37898 3c298f89-4303-0410-b956-a3cf2f4a3e73
The package makes it possible to create custom SPI
buses via GPIO lines.
This module is based on i2c-gpio-custom and allows to
configure an SPI bus via GPIO lines and expose it to
userspace without rebuilding the kernel. This is maily
intended to connect microcontrollers and other simple
SPI devices without making an ad-hoc kernel driver.
Signed-off-by: Marco Burato <zmaster.adsl@gmail.com>
[juhosg:
- change subject,
- extend and reformat commit message,
- cleanup checkpatch errors/warnings in module source]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37872 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thanks to Berni, Adam Novak and Sedat Dilek for patches and inspiration
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37866 3c298f89-4303-0410-b956-a3cf2f4a3e73
Backport some rt2x00 specific changes from
wireless-testing/master-2013-08-26 to add
support for RT3573 based devices.
Also refresh the rt2x00 specific patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37843 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was itriggered by to many non buffalo devices
This closes#14043.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37804 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is partly based on patches sent by Łukasz Kwestarz (See https://lists.openwrt.org/pipermail/openwrt-devel/2012-March/014356.html).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37802 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the "start_disabled" option in hostapd that was added
in the earlier patch.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37732 3c298f89-4303-0410-b956-a3cf2f4a3e73
