It was already increased for NAND devices so do the same for the ones
with serial memory.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r49207
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49208 3c298f89-4303-0410-b956-a3cf2f4a3e73
Reconfiguring the UART when the FIFO is not empty may cause the boot to
hang. This hang is extremely suspectible to timing differences; recompiling
the kernel with the same configuration, but different UTS_VERSION
timestamps can yield images that hang more or less often. Sometimes images
are produced that hang reproducibly.
This patch should also make it into one of the next linux-stable releases,
but it's better to get this fixed as soon as possible.
Fixes#21773, #21857.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r49156
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49202 3c298f89-4303-0410-b956-a3cf2f4a3e73
the fullduplex on CS1 is broken. remove the fullduplex support and run on
plain half duplex on both CS lines.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49201 3c298f89-4303-0410-b956-a3cf2f4a3e73
there is a deadlock that triggers under heavy bus load. until the bug is
fxed, revert to an old version of the I2C driver that does not suffer
from this issue.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49200 3c298f89-4303-0410-b956-a3cf2f4a3e73
We need to fix Seama just like we fix TRX due to the rootfs mark.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r48522
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49170 3c298f89-4303-0410-b956-a3cf2f4a3e73
14e4:d612 was found in D-Link DIR-885L and Netgear R8500. It's most
likely a bridge used by all 14e4:4365 BCM4366 devices.
Without this fixup device wasn't treated as a bridge:
[ 2.849895] pci 0000:00:00.0: ignoring class 0x020000 (doesn't match header type 01)
and didn't get its resources assigned. This resulted in child devices
not being able to get any resources (due to the parrent missing them):
[ 3.375428] pci 0000:01:00.0: BAR 2: no space for [mem size 0x00400000 64bit]
[ 3.387949] pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00400000 64bit]
[ 3.725797] pci 0000:01:00.0: BAR 0: no space for [mem size 0x00008000 64bit]
[ 3.738314] pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00008000 64bit]
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49118 3c298f89-4303-0410-b956-a3cf2f4a3e73
This moves few upstreamed patches and adds DIR-885L dts file. Please
note it doesn't mean this device is supported yet.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49115 3c298f89-4303-0410-b956-a3cf2f4a3e73
We can use one code path for BCM4707 rev. 4 and BCM53018.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49092 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apart from using our new building system there are 2 more changes:
1) Limit amount of images
So far we were generating all standard images (optimized one and two
with no loader) for every SUBTARGET. This is not needed, as e.g. the
only device requiring gzipped kernel is legacy Huawei E970.
2) Change output names
The new image building system requires specifying device name. This
forced picking some and resulted in:
openwrt-brcm47xx-$(SUBTARGET)-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-squashfs-gz.trx
openwrt-brcm47xx-$(SUBTARGET)-squashfs-noloader-nodictionary.trx
becoming:
openwrt-brcm47xx-$(SUBTARGET)-standard-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-standard-noloader-gz-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-standard-noloader-nodictionarylzma-squashfs.trx
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r49006
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49007 3c298f89-4303-0410-b956-a3cf2f4a3e73
This only drops WGR614 V9 which has 2 MiB flash and it's unlikely to get
any interest.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r48975
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@49003 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the kmod-mt76 package from the EX2700 profile to free up
around 100 KiB of space on the root filesystem.
This patch applies to both trunk and Chaos Calmer.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48887 3c298f89-4303-0410-b956-a3cf2f4a3e73
Commit r48849 changed the drivers/mtd/spi-nor/spi-nor.c file and broke
this patch in bcm53xx.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48871 3c298f89-4303-0410-b956-a3cf2f4a3e73
This enables booting from devices that use an ATI PATA controller for
the boot device, such as the embedded CF cards in Fujitsu-Siemens Futro
thin-clients.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Backport of r47304
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48861 3c298f89-4303-0410-b956-a3cf2f4a3e73
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r47420
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48860 3c298f89-4303-0410-b956-a3cf2f4a3e73
It seems there are two *different* versions on TL-WR941ND v6: Chinese
and European one. Currently supported by OpenWrt is Chinese one. Rename
firmware to make it clear.
For details see:
http://wiki.openwrt.org/toh/tp-link/tl-wr941ndhttps://forum.openwrt.org/viewtopic.php?id=59295
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r47107
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48859 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Backport of r46283
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48857 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Backport of r46282
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48856 3c298f89-4303-0410-b956-a3cf2f4a3e73
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.
Fix Ethernet by setting the right values.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Backport of r46281
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48855 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch cherry-picked from the following location:
https://www.codeaurora.org/cgit/quic/qsdk/oss/system/openwrt/commit/?h=release/coconut_ioe4531_2.0&id=5c357bf6c763e4140dddcc9a3bc5f005525a9c0e
Changelist,
- add more register defines
- add EHCI support
- fix GPIO pin count to 18
- fix chained irq disabled
- fix GMAC0/GMAC1 initial
- fix WMAC irq number to 47
- merge the changes of dev-eth.c from the patch to file.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r46207
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48854 3c298f89-4303-0410-b956-a3cf2f4a3e73
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r46206
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48853 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Backport of r48279
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48852 3c298f89-4303-0410-b956-a3cf2f4a3e73
The ubdev01 profile defines its own MTDPARTS with smaller firmware
partition, so give it its own UBNT_BOARD in mkfwimage.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r48828
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48847 3c298f89-4303-0410-b956-a3cf2f4a3e73
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r47553
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48844 3c298f89-4303-0410-b956-a3cf2f4a3e73
The hardware of the v3 is identical to the v2.
Based-on-patch-by: Andreas Ziegler <github@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r47406
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48843 3c298f89-4303-0410-b956-a3cf2f4a3e73
Install uboot files to KERNEL_BUILD_DIR instead of BIN_DIR to fix
ImageBuilder. Similar fixes are necessary for many (all?) other uboot
targets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r46605
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48835 3c298f89-4303-0410-b956-a3cf2f4a3e73
The DTS files aren't useful (other targets don't copy them either) and
clutter BIN_DIR with files unrelated to the chosen profile.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r46604
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48834 3c298f89-4303-0410-b956-a3cf2f4a3e73
This device is identical to the TL-WR740N v5, it even uses the same HWID (which
wasn't the case for older TL-WR741ND revisions).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport of r46238
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48833 3c298f89-4303-0410-b956-a3cf2f4a3e73
TP-Link ships wr740n v5.0 to Romania (so probably everywhere except
China) with 4 MB flash and 32 MB memory (confirmed by their local
support). This patch adds support for the v5.0 clone of v4, i just
tested it on my own v5.0 router and it works.
Signed-off-by: Daniel Petre <daniel.petre@posteo.net>
Backport of r46115
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48832 3c298f89-4303-0410-b956-a3cf2f4a3e73
compat-wireless/backports now contains a bcm47xx_nvram.h file to
backport some of the functions in it which are used by the bcmfmac
driver. This file just checks for the kernel versions and provide an
empty implementations on older kernel versions. This is OK on most
systems, but on bcm47xx / bcm53xx systems we want to call the real
functions here. This commit removes the file from backports in our
build process like we do it with the bcma and ssb header files. Instead
we add a recent version into our kernel so all code uses only one
header file. On bcm47xx / bcm53xx the real implementations of this code
will be used.
Reported-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[Backport of r47467. The recent mac80211 backport was missing this patch,
breaking the build of the brcmfmac module]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@48831 3c298f89-4303-0410-b956-a3cf2f4a3e73
