Signed-off-by: Christian Beier <cb@shoutrlabs.com>
Backport of r46047
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46057 3c298f89-4303-0410-b956-a3cf2f4a3e73
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Backport of r46046
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46056 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
Backport of r46044
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46054 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r46032
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46033 3c298f89-4303-0410-b956-a3cf2f4a3e73
It seems that there are maximum timings for mdio accesses that can be
hit when the system is under load and the thread is scheduled during
a read or write access. Since there is no way of knowing if this
happens as there is not even a parity bit, try to work around it
by disabling interrupts during any gpio-mdio accesses.
Performance impact seems to be neglectable, as mdio accesses are not
that often.
Hopefully fixes#19500.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Backport of r46012.
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46016 3c298f89-4303-0410-b956-a3cf2f4a3e73
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45970 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds the pll_1000 value for eth0 interface. This makes the Rocket M
XW image compatible with other Ubiquiti devices with similar hardware with a
Gigabit Ethernet port.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45965 3c298f89-4303-0410-b956-a3cf2f4a3e73
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes#19751, bug introduced in #45624
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45958 3c298f89-4303-0410-b956-a3cf2f4a3e73
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45954 3c298f89-4303-0410-b956-a3cf2f4a3e73
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45919 3c298f89-4303-0410-b956-a3cf2f4a3e73
The v1 identifies as v10 internally. As there is no TL-WA830RE v10, add a
workaround to avoid confusing users.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45903 3c298f89-4303-0410-b956-a3cf2f4a3e73
Building the loader in Image/Build/TPLINK-SAFELOADER would break the image
builder as no target compiler is available in that stage.
Fixes#19580
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45855 3c298f89-4303-0410-b956-a3cf2f4a3e73
In contrast to Image/BuildLoader, Image/BuildLoaderPatched first patches the
kernel command line in the image and then builds the loader without command
line. This allows building loaders for systems which don't boot correctly when
the kernel command line is provided by the loader (like the TP-LINK CPE series).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45854 3c298f89-4303-0410-b956-a3cf2f4a3e73
move the patch to the proper folder
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45848 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is the case e.g. if JFFS2 partition is full.
see: https://www.mail-archive.com/linux-unionfs@vger.kernel.org/msg00246.html
(a small error in a logmessage was changed and reported upstream)
runtime tested on ar71xx with kernel 3.18.11 and r45772
this paritially fixes#19564
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
Acked-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45833 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45726 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties.
v2: set correct DEVICE_PROFILES for all images.
v2: migrate TP-LINK TL-WR710N v2 which was committed after v1.
v2: split very very long line `TARGET_DEVICES +=` into smaller parts
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45643 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45640 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45639 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45638 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45637 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45636 3c298f89-4303-0410-b956-a3cf2f4a3e73
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45635 3c298f89-4303-0410-b956-a3cf2f4a3e73
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45634 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45633 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45632 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45631 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45630 3c298f89-4303-0410-b956-a3cf2f4a3e73
It has been broken since the new ath10k firmware introduced in r44656.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45624 3c298f89-4303-0410-b956-a3cf2f4a3e73
Moved board to the right magic case.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45588 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45553 3c298f89-4303-0410-b956-a3cf2f4a3e73
TP-Link TL-WR710n v2 looks like v1, but has less memory (4MB).
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45538 3c298f89-4303-0410-b956-a3cf2f4a3e73
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45524 3c298f89-4303-0410-b956-a3cf2f4a3e73
