This patch add mesh_param support in mac80211.sh
It suppose that this patch http://patchwork.openwrt.org/patch/3540/ is applied (add HT support for mesh)
Tested with rspro(ar9280)/wr1043nd, BB r36211
see also this http://lists.open80211s.org/pipermail/devel/2012-June/003352.html
(mesh_hwmp_rootmode 1 & mesh_gate_announcements 1
=> mesh_hwmp_rootmode 4 & mesh_gate_announcements 1)
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36640 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Add support for IP-in-IPv6 tunnels (DS-Lite)
* Use source-based routing for IPv6 to allow multi-wan
* Various smaller tunnel setup improvements
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36627 3c298f89-4303-0410-b956-a3cf2f4a3e73
grub-editenv allows to modify grub2 environment files. Add a new package
that build grub2 for the target and packs up grub-editenv.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36574 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch simply adds support for the "--proxy-dnssec" command in dnsmasq into the init file so it can be used with /etc/config/dhcp.
Signed-off-by: Adam Gensler <openwrt@kristenandadam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36570 3c298f89-4303-0410-b956-a3cf2f4a3e73
Previously if the upstream router did not provide any DHCPv6-service
the wan6 interface would not come up even if RAs were received. The new
behavior allows the wan6 interface to comeup with RA-only configuration
after a timeout of 10s.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36555 3c298f89-4303-0410-b956-a3cf2f4a3e73
- assume "tcp+udp" if no protcol is specified in rules or redirects (#13422, #13386)
- add support for fwmark matches and mark setting targets
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36521 3c298f89-4303-0410-b956-a3cf2f4a3e73
- copy permission of config files to state files to allow access to state info by non root users
- properly handle empty string case when unsetting lists
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36518 3c298f89-4303-0410-b956-a3cf2f4a3e73
In my machine, the file is created with arptable_filter before
arp_tables. This can't happen because the former depends on the
latter.
So, instead of rely on wildcards (*.ko), set by hand the files to
be loaded in the correct order.
Signed-off-by: Jonh Wendell <jonh.wendell@oiwifi.com.br>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36512 3c298f89-4303-0410-b956-a3cf2f4a3e73
libiptc.pc depends on libip[4|6]tc.pc, thus all of those need to be
installed.
Should fix collectd build and thus #13146; which should make collectd
appear in snapshots again.
Signed-off-by: Danny Baumann <dannybaumann@web.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36509 3c298f89-4303-0410-b956-a3cf2f4a3e73
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36482 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hardcoding channel number to 11 is a bad idea, it may be even not
available on some devices. If there are two single-band radios, the
one for 5GHz doesn't have 11 channel.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36479 3c298f89-4303-0410-b956-a3cf2f4a3e73
To add support for core rev 28 there are a lot more changes needed.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36477 3c298f89-4303-0410-b956-a3cf2f4a3e73
