The driver seems to be causoing boot rpoblems on some SoCs
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37314 3c298f89-4303-0410-b956-a3cf2f4a3e73
* improves logread over net code
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37313 3c298f89-4303-0410-b956-a3cf2f4a3e73
this fixes a stack corruption in kmodloader. lsmod should be fixed now
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37312 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is now controlled by a module parameter and the default
configuration depends on brcmsmac being installed.
This patch causes b43 to take core rev 17 and 18 always by default.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37307 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37304 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes some problems with the switch handling
* It now send the messages again to indicate a button for failsafe mode should be pressed
* it does not leak packages between wan and lan any more
* the switch works again in normal mode
The Ethernet connection has to be up when the switch driver switch-robo
is insmoded therefor we just do it again.
Explicitly set enable_vlan to prevent leaking packages.
This should close#13869, #13868 and #13716
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37286 3c298f89-4303-0410-b956-a3cf2f4a3e73
add the boot flag to make the kernel modules needed for Ethernet and
diag load on startup.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37284 3c298f89-4303-0410-b956-a3cf2f4a3e73
In kernel 3.10 the proc interface changed, this patch adds the changes needed for the new interface.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37280 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was done to reduce the number of forward declaration needed.
This does not contain any real change in the code.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37278 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apparently there are some broken devices out there that have the local
bit already set in the factory MAC address. Move the | 0x2 over to the
other side of the xor operation to fix this without affecting devices
with proper addresses.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37269 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was only tested on a Netgear R6250, but it could also work on
other devices when the correct images are generated.
It is only possible to boot into a ram disk, no Ethernet, Wifi, flash,
USB is supported.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37268 3c298f89-4303-0410-b956-a3cf2f4a3e73
this fixes a regression in the watchdog init code
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37259 3c298f89-4303-0410-b956-a3cf2f4a3e73
Reported-by: Matti Laakso
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37258 3c298f89-4303-0410-b956-a3cf2f4a3e73
