Bump dnsmasq to v2.73rc8
Important - fixes remotely exploitable buffer overflow introduced in all v2.73 test/release candidates.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45693 3c298f89-4303-0410-b956-a3cf2f4a3e73
This device seems to have switch port 7 connected to the CPU:
vlan1ports=1 2 3 5 7*
vlan2ports=0 7u
it should be handled by eth1 and NVRAM seems to confirm that (no
et0macaddr entry, existing et1macaddr & et1phyaddr entries).
One of the remaining ports (4/8?) may be connected to the Quantenna SoC.
Original firmware boot log contains following messages:
(0x00,0x5d)Port 5 States Override: 0xfb
(0x00,0x5f)Port 7 States Override: 0xfb
(0x00,0x0e)Port 8 States Override: 0x0a
(why does it force port 5 state?!)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45692 3c298f89-4303-0410-b956-a3cf2f4a3e73
It has 3 Ethernet interfaces, each of them connected to separated switch
port. Default NVRAM uses switch port 8 as CPU which is connected to the
3rd interface (eth2).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45681 3c298f89-4303-0410-b956-a3cf2f4a3e73
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45676 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.
[ 2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.970000] 2 netgear-fw partitions found on MTD device firmware
[ 2.970000] 0x000000070000-0x000000188440 : "kernel"
[ 2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs"
The patch removes the rather useless warning message.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45669 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/ (patches 110-111)
We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45663 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.
It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45662 3c298f89-4303-0410-b956-a3cf2f4a3e73
ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended
on most ARM architectures. This automatically calculate ZRELADDR by
masking PHYS_OFFSET with 0xf8000000.
On IPQ806x though, the first ~20MB of RAM is reserved for the hardware.
In newer bootloader, when DT is used, this is not a problem, we just
reserve this memory in the device tree. But if the bootloader doesn't
have DT support, then ATAGS have to be used. In this case, the ARM
decompressor will position the kernel in this low mem, which will not be
in the RAM section mapped by the bootloader, which means the kernel will
freeze in the middle of the boot process trying to map the memory.
As a work around, this patch allows disabling AUTO_ZRELADDR when
ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders
which don't support device-tree, which is the case on certain early
IPQ806x based designs.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45661 3c298f89-4303-0410-b956-a3cf2f4a3e73
As mkits.sh makes the -d argument optional, we'll make this same
argument optional in the MkFIT function as well.
With this change, MkFIT can be used both to generate FIT images with DT,
and without DT.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45660 3c298f89-4303-0410-b956-a3cf2f4a3e73
mkits.sh help currently shows dtb file as optional, but generates an
invalid its file when this option is unspecified.
We're fixing this problem by removing the use of the sed command and
just including variables instead.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45659 3c298f89-4303-0410-b956-a3cf2f4a3e73
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45658 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most of the time, we want to make sure OpenWrt has been configured and
setup before start running make. However, in case of package/symlinks,
forcing prereq as a dependency creates multiple issues:
*when executed on a clean workspace, it will prompt for user input
and open a menuconfig window before executing the feeds command
*the only way around that is to provide a .config. However, the "prereq"
target would then run a "make defconfig", which will remove all the
packages in the .config but from external feeds, as feeds have not been
installed yet.
The only way to currently work around this, is to generate a fake config
by running "make defconfig", then "make package/symlinks", copy the real
config (which at this point disregards the previously generated config),
and run make defconfig again. Something like this:
make defconfig
make package/symlinks
cp real.config .config
make defconfig
This change is removing the need for the first defconfig, making the
process more logical for OpenWrt users using the package/symlinks target.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45657 3c298f89-4303-0410-b956-a3cf2f4a3e73
